Knowledge

Freeze dryer working principle and components

Working principle and components of vacuum freeze dryer! Vacuum freeze-drying is to first freeze the material below the eutectic point temperature so that the moisture in the material becomes solid ice, and then the ice is directly sublimated into water vapor under an appropriate vacuum degree. The water vapor is condensed by the water vapor condenser (water trap) in the vacuum system to obtain the technology of drying products. The three stages of the freeze-drying process are divided into pre-freezing, sublimation drying, and analytical drying.

The structure of a vacuum freeze dryer (freeze dryer) is mainly composed of six parts: drying box, condenser (water catcher), heating system, vacuum system, refrigeration system, and electrical control system.

1.1 Drying oven

The drying box is a kind of airtight that can be vacuumed and heated. The sublimation and drying process of the material is completed in the drying room. The material is placed in the stainless steel tray on the shelf in the drying room, and the area of each square tray is 8~12 kg. There is a probe for measuring the temperature of the material on each shelf to monitor the temperature of the material throughout the freeze-drying process. The door adopts a rubber sealing strip, and attention should be paid to tightening the handle on the door when closing the door to ensure that the inside of the box is sealed.

1.2 Condenser (water catcher)

The condenser is a closed device for condensing and sublimating water vapor. There is a large area of metal adsorption surface inside. The water vapor sublimated from the drying box material can be condensed and adsorbed on its metal surface. The working temperature of the adsorption surface can reach - 45 ℃~- 55℃, the shape of the condenser is a cylinder made of stainless steel or iron, and there are condenser pipes in the inner plate, which are respectively connected with the refrigeration unit to form a refrigeration cycle system. The condenser and the drying box are connected by a vacuum butterfly valve; a vacuum system is formed by connecting a stainless steel pipe and a vacuum pump set. The upper part of the condenser pipe in the cylinder is equipped with a defrosting water spray pipe, which is connected with the water pipe through a vacuum diaphragm valve, which is to ensure the defrosting water. Do not enter the drying oven and vacuum line. The outside of the condenser is insulated with a foamed plastic plate, and the outermost layer is covered with a stainless steel plate.

66

1.3 Heating system

The function of the heating system of the freeze dryer is to heat the materials in the drying box so that the materials can continuously obtain the heat of sublimation so that the items can meet the specified moisture content requirements. The heating system of the freeze dryer has different heating methods. , we use the circulating medium heating method. The circulating heating system consists of a pipeline pump, circulating medium tank, heater, inlet and outlet pipelines, liquid temperature controller, etc. The circulating liquid can be composed of 4 parts of water, 2 parts of ethanol, and 4 parts of ethylene glycol to form a circulating antifreeze liquid. Its freezing point is -120°C, and the maximum liquid temperature does not exceed 60°C during use. Now, most freeze-drying equipment has adopted silicone oil. as circulating fluid. When the heating system is working, the circulating liquid is heated first, and the liquid temperature is automatically controlled and heated by the temperature selected by the liquid tank control regulator. After the pipeline pump is turned on, the circulating liquid can be sent to the shelf in the drying box, and the shelf Heat, then return to the tank for the heating cycle. In radiation or heating, we use steam to heat up to a maximum temperature of 120°C, and the temperature is automatically controlled by a steam solenoid valve.

1.4 Vacuum system

The vacuum system consists of a rotary vane vacuum pump or a water ring pump and a Roots vacuum pump. The Roots pump cannot be used alone as a booster pump. The rotary vane pump or the water ring pump must be started first to make it work for a period of time. When it reaches below 1Kpa, the Roots pump will be started automatically. See the manual for the structure of the rotary vane pump and Roots pump. The vacuum gauge of the vacuum system can use an electric contact vacuum gauge, which can automatically control the start of the Roots pump according to the pre-selected vacuum value. There is a vacuum butterfly valve in the vacuum pipeline between the drying box and the condenser, which can be opened and closed at any time according to the requirements of use. The vacuum pump pipeline is equipped with an electromagnetic air release shut-off valve. When the vacuum pump stops working, the vacuum pipeline can be automatically closed, and the air is put into the pump at the same time to prevent the vacuum pump oil from being played back into the vacuum pipeline due to the negative pressure. There are corrugated hoses between them to prevent vibration during operation.

1.5 Refrigeration system

The refrigeration system of the freeze dryer consists of a refrigeration compressor unit (including a water-cooled condenser, oil separator, high-pressure pipeline, dry filter, expansion valve, evaporator, and low-pressure pipeline), and adopts a Freon unit and R22 refrigerant or fluorine refrigeration. The unit and the refrigeration unit are composed of a refrigeration system and a water catcher refrigeration system for quick freezing of freeze-dried products. When the system is in operation, the shelf temperature can be reduced to - 35°C in contact heating mode. When the refrigeration system is working, the surface temperature of the condensing coil can reach -35~-55℃. According to customer needs, single-stage or two-stage refrigeration compressor units are used, and the refrigeration effect is good.

1.6 Electrical Control System

The electrical control system of the freeze dryer consists of automatic devices and circuits such as computer display recorders, consoles, control instruments, and adjustment instruments. Its function is to manually or automatically control the freeze dryer to control the normal operation of the equipment. A console is a centralized group of recording control instruments for temperature and vacuum inspection instruments and switches for each unit. The dashboard of the console is equipped with temperature and vacuum inspection instruments, vacuum gauges for drying ovens and vacuum pumps, and temperature indicating regulators. The liquid temperature-control regulator, timing clock, etc. The buttons of each unit are equipped with switches, etc.

The freeze dryer is also equipped with interlock protection devices, such as ① the heating pipe cannot work when the front box is cooled. ②The Roots pump cannot be started if the vacuum gauge is less than the set value. ③The cooling water is not provided, and the refrigeration unit does not start. ④Vacuum pump, solenoid valve with air release shut-off valve, and vacuum pump power meter are connected together and work at the same time. ⑤The shelf is heated at a constant temperature, controlled by a temperature indicating regulator.


You Might Also Like

Send Inquiry